Soil compaction occurs when soil particles are compressed, reducing pore space, and increasing the mass of soil solids per unit volume (density). Pressure exerted by machinery and foot traffic is a common cause of compaction at the surface, and moist soils are more at risk for compaction. Soil compaction can be so significant that the soil bulk density of well-used lawn soil approaches the bulk density of concrete. When soil particles are pressed together, it reduces the pore space, which causes an increase in bulk density and a decrease in infiltration, resulting in a larger volume of runoff. It is important also to note that the maximum density of a soil is dependent upon the percent of moisture in the sample. To check for suitable soil physical properties, one can monitor soil bulk density and water movement.
Soil Texture
Soil texture—referring to the proportions of sand, silt, and clay— affects drainage, root penetration, and water-holding capacity. Soil tests often include a particle size analysis to identify the texture class (e.g., loam, clay, sandy loam). Understanding soil texture helps in choosing suitable crops and amending the soil to improve its physical properties.
Bulk Density
A soil density of 1.65 g/cm3 is considered sufficiently dense so that roots cannot penetrate the soil. One can approximate bulk density without fancy equipment. How do I find out of my soil has a poor bulk density (Figure 3)?
- You first need a volume of soil. You can dig a hole and cut a 3-d block of soil. Save the soil and rocks and measure the three dimensions of the hole (length, width, depth. Determine the volume by multiplying the 3 dimensions.
- Alternatively, you can use a metal ring cut from a thin-walled 5-7 cm pipe.
- Calculate the ring's volume using geometry. V = πr²h where "π" is a mathematical constant (approximately 3.14), "r" is the radius of the ring's base (circular top), and "h" is the height of the ring; essentially, multiply the area of the base (πr²) by the height to find the volume.
- Fill the ring with soil in the field by pressing it into the soil or scooping it in (less accurate). You can also tap the ring in with a mallet; placing a flat board across the top may make using the mallet easier.
- Place the soil and rocks in a microwave for about 3-4 min or an oven at 450 °F for several hours to remove as much moisture as possible (or leave in the sun for a day but not overnight).
- Use a 2 mm screen (or screen close to 2mm) to sieve the soil. Weight the rocks and soil separately.
- Divide the mass of soil by the volume you calculated. Alternatively, weigh the soil and rocks together and divide by the volume. The below bulk density data uses a rock-free estimate, but plants don't like to grow into rocks so some growers use the rocks with the soil to estimate bulk density limits.
A soil density of 1.60 g/cm3, or 100 lbs/ft3, is considered the maximum density that roots can penetrate (USDA-NRCS, 2026). Different soil textures have different densities, and soil compaction will increase bulk density (Table 3).
| Soil Texture | Ideal bulk density for plant growth (g/cm³) | Bulk density that affects root growth (g/cm³) | Bulk density that restricts root growth (g/cm³) |
|---|---|---|---|
| sand, loamy sand | <1.60 | 1.63 | >1.80 |
| sandy loam, loam | <1.40 | 1.63 | >1.80 |
| sandy clay loam, clay loam | <1.40 | 1.6 | >1.75 |
| silt, silt loam | <1.40 | 1.6 | >1.75 |
| silt loam, silty clay loam | <1.40 | 1.55 | >1.65 |
| sandy clay, silty clay, clay loam | <1.10 | 1.49 | >1.58 |
| clay (<45% clay) | <1.10 | 1.1 | >1.47 |

Figure 3. Bulk density sampling
Water movement
Saturated hydraulic conductivity (Ksat) is a measure of how easily water moves through soil and is typically expressed in units of length per time, such as cm/hr. The measure can be made at the surface (infiltration) or at a specific depth in the subsurface (percolation). When designing a garden, it is important to consider the soil’s Ksat to ensure good drainage and prevent waterlogging. A Ksat that is too low can lead to waterlogged conditions, which can damage plant rots and limit plant growth. A Ksat that is too high can lead to water draining too quickly and not being available for plants to use.
A Ksat for good drainage in a garden generally falls within the range of 5 to 13 cm/hr. However, the best Ksat value for a garden will depend on the types of plants being grown and the specific soil conditions (Kays, 2014; PADEP, 2025).
For example:
- Turf soils may have higher drainage rates, but rates above 5 to 8 cm/hr can cause the soil to dry out very quickly.
- Many landscape designers create soils that are blended to achieve a Ksat of about 5 to 13 cm/hr.
- Rates of 13 to 25 cm/hr or more are typical of structural soils and stormwater bioretention soils.
For natural undisturbed soils, a drainage rate as low as 0.3 cm/hr can still support plant growth. Soils with a Ksat less than or equal to 0.6 cm/hr are considered limited for drainage and soils with a Ksat between 0.6 and 1 cm/hr are considered marginal. If the Ksat of a soil is less than 0.6 cm/hr, the use of an underdrain (like a French drain with gravel) may be needed. Soils with Ksat values more than 25 cm/hr drain too fast for gardens and the soil will be too droughty.
There are many different methods to measure Ksat such as double ring infiltrometer, tension infiltrometer, and constant head borehole permeameter. You can make a simple single or double ring infiltrometer yourself using a small soup can and/ or a large #10 can (Figure 4). Instructions for how to run either test are common to download freely from the Internet.

Figure 4. Simple saturated conductivity measurements (Exhibit A is a single ring infiltrometer and exhibit B is a double ring infiltrometer.)
Overall, when selecting soils for a garden, it is important to consider the saturated hydraulic conductivity (Ksat), as this will affect the rate at which water drains from the soil and therefore the availability of water to the plants. Take the time to at least make a few simple surface single ring measures (infiltration). You can also dig shallow holes and measure layers below the surface that you suspect are limiting water movement in the subsoil (percolation). If the soil’s Ksat is too low, it will be poorly drained, and if it is too high, water will drain too quickly. An ideal Ksat for most garden applications falls between 5 and 13 cm/hr.
Institute for Sustainable Agricultural, Food, and Environmental Science
Address
111 Ferguson BuildingUniversity Park, PA 16802-2600
- Email safes@psu.edu
Institute for Sustainable Agricultural, Food, and Environmental Science
Address
111 Ferguson BuildingUniversity Park, PA 16802-2600
- Email safes@psu.edu